1. Connect the brake pedal together when the wrecker is walking on the road.
2. Correctly adjust the brake system of the wrecker.
3. Check the condition of the vehicle and tire inflation before driving the wrecker.
4, when walking on the road to open the wrecker's headlights and flashing lights.
5, "slow vehicles" logo should be hung in the wrecker or drag trailer obvious place.
6. If the weight of the wrecker is greater than the wrecker, do not drag it downhill.
7. Drag the heavy object uphill and downhill to hang the same file.
8, when the wrecker engine shutdown device to maintain a good working condition.
9. Keep the wrecker battery and starter system in good working condition.
10. When the wrecker is suddenly started, be sure to open the gear and turn the crank in the driver's seat.
11. Double-entry equipment must be equipped with a reversing alarm that can be heard.
Operation method:
1. Disengage the winch clutch and pull the cable to the vehicle to be carried, and hook the “j†hook on the towed shackle on the lower part of the towed vehicle. Then engage the winch clutch. Note that when the cable is pulled out, the number of remaining steel wire loops must not be less than 5 turns.
2. The neutral position of the vehicle being carried is to release the parking brake of the vehicle being carried.
3. Control the winch lever, pull the car onto the platform, and control the j-shaped hook on the cable to be more than 0.4m away from the winch. When the winch is under load, do not disengage the manual control clutch of the winch. This will damage the winch. Note: When using the chain hook to win the accident using the winch, especially the bottom of the chassis of the car, be very careful not to damage the site of the trailer, so as not to cause unnecessary trouble.
4. When the loaded vehicle has been dragged into place, tie the rear tire with a safety tie and tighten the loaded vehicle diagonally to the flat rings on both sides. Note: If the safety ring is broken, the safety bandage should be wrapped around the sturdy parts of the car. For safety bandages that cannot be manually locked, the winch lever can be maneuvered to maneuver the winch and move the loader forward a little to properly tension the safety chain.
5. When a flat-type road wrecker is used to fix a faulty car with a strap on a flat plate, all four straps must be locked on the wheel or the body.
6, strap ratchet lock must be closed.
Note: Nylon straps will be loose during long-term tension. Check the tightness of the bandage regularly during operation. Especially in the case of poor road conditions or sudden braking, check the tightening to avoid accidents.
7. The control platform tilts the joystick so that the tail of the platform rises 0.15m above the ground.
8. The control platform tilts the joystick so that the platform moves forward to about 0.6m from the frontmost position. The control platform tilts the joystick to return the platform to the horizontal position.
9, control platform sliding joystick, is the platform to move forward to the front.
10. In order to prevent the possible damage to the winch caused by the vibration of the wire rope due to vibration during the next driving, the front end of the vehicle must be fixed with the other two safety chains and tightened as much as possible. Load positioning and tension.
11. The car will be loaded with a file and the handbrake will be pulled.
12. Check that all safety chains or chains and connections are secure and tensioned.
13. After the above steps are completed, follow-up work procedures are performed. Depress the clutch of the road wrecker, remove the power take-off, and complete the platform loading operation.
2. The neutral position of the vehicle being carried is to release the parking brake of the vehicle being carried.
3. Control the winch lever, pull the car onto the platform, and control the j-shaped hook on the cable to be more than 0.4m away from the winch. When the winch is under load, do not disengage the manual control clutch of the winch. This will damage the winch. Note: When using the chain hook to win the accident using the winch, especially the bottom of the chassis of the car, be very careful not to damage the site of the trailer, so as not to cause unnecessary trouble.
4. When the loaded vehicle has been dragged into place, tie the rear tire with a safety tie and tighten the loaded vehicle diagonally to the flat rings on both sides. Note: If the safety ring is broken, the safety bandage should be wrapped around the sturdy parts of the car. For safety bandages that cannot be manually locked, the winch lever can be maneuvered to maneuver the winch and move the loader forward a little to properly tension the safety chain.
5. When a flat-type road wrecker is used to fix a faulty car with a strap on a flat plate, all four straps must be locked on the wheel or the body.
6, strap ratchet lock must be closed.
Note: Nylon straps will be loose during long-term tension. Check the tightness of the bandage regularly during operation. Especially in the case of poor road conditions or sudden braking, check the tightening to avoid accidents.
7. The control platform tilts the joystick so that the tail of the platform rises 0.15m above the ground.
8. The control platform tilts the joystick so that the platform moves forward to about 0.6m from the frontmost position. The control platform tilts the joystick to return the platform to the horizontal position.
9, control platform sliding joystick, is the platform to move forward to the front.
10. In order to prevent the possible damage to the winch caused by the vibration of the wire rope due to vibration during the next driving, the front end of the vehicle must be fixed with the other two safety chains and tightened as much as possible. Load positioning and tension.
11. The car will be loaded with a file and the handbrake will be pulled.
12. Check that all safety chains or chains and connections are secure and tensioned.
13. After the above steps are completed, follow-up work procedures are performed. Depress the clutch of the road wrecker, remove the power take-off, and complete the platform loading operation.
Darkening Welding Helmet,Auto Darkening Welding Helmet
Zhengtai Welding Equipment Co., Ltd. , http://www.ztweldingmachine.com